| 以文本方式查看主題 - 曙海教育集團論壇 (http://www.hkzrsy.com/bbs/index.asp) -- Wince技術討論區 (http://www.hkzrsy.com/bbs/list.asp?boardid=9) ---- ok6410 sd卡一鍵燒錄問題 (http://www.hkzrsy.com/bbs/dispbbs.asp?boardid=9&id=1388) |
| -- 作者：wangxinxin -- 發布時間：2010-11-16 14:14:42 -- ok6410 sd卡一鍵燒錄問題 一鍵燒錄SD卡遇到問題如下： 1：啟動開關設置:1,2,3 為0；4，5，6，7，8 為1; 2:按一鍵燒錄說明燒好SD卡（4G），插入開發板； 3：接上串行線，USB線 4：開啟dnw; 5:接通開發板電源； 電腦提示：無法識別USB設備。試圖安裝，找遍飛凌公司提供的盤片資料（包括dnw下載驅動），沒有合適的驅動可安裝。。 dnw信息區顯示： =============== USB Receive Test ============== Error: can\'t receive data from the USBD =============================================== Welcome! This tool just for TE/OK6410 +OALArgsInit() SocID:0x36410101 Arguments area is initialized -OALArgsInit() INFO: (unsigned)C_IsrHandler : 0x8006684C INFO: (unsigned)ASM_IsrHandler : 0x8006861C INFO: (unsigned)pISR : 0xEA01A17F HSMMC init [HSMMC1] Setting registers for the EPLL (for SDCLK) : SYSCon. [HSMMC0] Setting registers for the GPIO. [HSMMC1] Setting registers for the EPLL : HSMMCCon. #### this SD card is made on SPEC 2.0 This SD card is made on SPEC 2.0 This SD card is High Capacity CardSize: 7729152 sector [HSMMCLIB:INF] ClockConfig() Card Working Frequency = 24MHz BP_Init [FMD] ++FMD_Init() **** [FMD:INF] FMD_Init() : Read ID = 0x0000ecd3 [FMD] FMD_Init() : NUM_OF_BLOCKS = 4096 [FMD] FMD_Init() : PAGES_PER_BLOCK = 128 [FMD] FMD_Init() : SECTORS_PER_PAGE = 4 [FMD] --FMD_Init() [FMD] FMD_GetInfo() : NUMBLOCKS = 4096(0x1000), SECTORSPERBLOCK = 128(0x80), BYTESPERSECTOR = 2048(0x800) [FMD] FMD_GetInfo() : NUMBLOCKS = 4096(0x1000), SECTORSPERBLOCK = 128(0x80), BYTESPERSECTOR = 2048(0x800) wNUM_BLOCKS : 4096(0x1000) [Eboot] ++InitializeDisplay() [Eboot] --InitializeDisplay() Press [ENTER] to launch image stored on boot media, or [SPACE] to enter boot monitor. Initiating image launch in 3 seconds. Starting auto-download ... Erase the block \'0..3\' System ready! Preparing for download... IsCardInserted g_pDownPt = 0xA300211B BL_IMAGE_TYPE_MANIFEST BL_IMAGE_TYPE_UNKNOWN Download BIN file information: ----------------------------------------------------- [0]: Base Address=0x0 Length=0x2000 ----------------------------------------------------- ----------------------------------------------(文件較大，省略一部分） chainInfo.dwLoadAddress: 0X00000000 chainInfo.dwFlashAddress: 0X00000000 chainInfo.dwLength: 0X00000000 } waitforconnect INFO: using TOC[1] dwJumpAddress: 0x80157734 INFO: OEMLaunch: Jumping to Physical Address 0x50157734h (Virtual Address 0x80157734h)... 鼿Windows CE Kernel for ARM (Thumb Enabled) Built on Sep 25 2009 at 11:04:23 [OAL] ++OEMInit() [OAL] S3C6410_APLL_CLK : 532000000 [OAL] ARMCLK : 532000000 [OAL] HCLK : 133000000 [OAL] PCLK : 66500000 [OAL] InitializeGPIO() [OAL] InitializeCLKSource() [OAL] InitializeCLKGating() [OAL] InitializeBlockPower() DCache: 128 sets, 4 ways, 32 line size, 16384 size ICache: 128 sets, 4 ways, 32 line size, 16384 size +OALArgsInit() Arguments area has some values -OALArgsInit() +OALTimerInit( 1, 33249, 0 ) -OALIntrRequestSysIntr(irq = 38, sysIntr = 16) [OAL] --OEMInit() //停在此處 開發板液晶顯示花屏。 注：在Nand 上啟動WINCE 正常。ActiveSync 工作正常。 請教飛凌公司工程師， 1 我的操作正確嗎？ 2 SD卡，讀卡會有問題？ 3 4G以上SD卡燒錄軟件是否成熟？ |